尾缘锯齿降低叶栅噪声的数值模拟

采用大涡模拟与声类比的方法研究了尾缘锯齿对涡轮叶栅噪声的影响.设计了两种不同的尾缘锯齿,对比了Re=3.3×105(基于叶片弦长与叶栅出口速度)下两种不同结构锯齿尾缘叶栅与直尾缘叶栅的声功率.结果表明:尾缘锯齿可以降低叶片吸力面边界层分离噪声约5dB,降低尾缘涡脱落噪声约10dB.进一步的研究表明,尾缘锯齿可以降低叶片尾缘附近表面的压力脉动幅值约50%,将展向相关尺度较大的涡破碎成展向相关尺度较小的涡,并消除尾缘脱落涡,这三者的综合作用使噪声得到降低.      

离心叶轮全三维反问题方法设计误差稳定性研究

用流线曲率全三维反问题方法和引入滑移因子模型的准三维流线曲率反问题方法设计了叶片数不同的和增压比不同的小型高速离心叶轮.用商用计算流体力学(CFD)求解器估算了这些叶轮的性能.对比了这两种反问题方法的设计误差稳定性,考察了分流叶片对设计误差的影响.结果表明,流线曲率全三维反问题方法能够根据叶片负荷对叶片设计做出恰当调整.较准三维反问题方法,流线曲率全三维反问题方法所设计叶轮的增压比普遍偏高.随叶片负荷增加,较准三维反问题方法,流线曲率全三维反问题方法的设计误差变化较小,即其设计误差稳定性明显较好.分流叶片对准三维反问题方法设计结果的影响明显较小.      

上下游干涉对转子叶片颤振特性的影响

使用自行开发的非定常流动数值模拟程序,分别考虑上、下游叶排干涉作用对转子叶片的颤振特性进行了研究,分析尾迹和势干扰对气动阻尼的影响规律.对转子叶片表面非定常压力进行傅里叶变换,使用能量法计算气动阻尼,研究不同叶片排轴向间距下气动阻尼的变化.通过考虑转静干涉效应的气动阻尼与单转子结果对比,总结了干涉作用对叶片颤振特性的影响规律;结果表明:上游导叶与转子一倍弦长间距时,获得正气动阻尼,与单转子预测的气动弹性稳定性结果相反.说明在进行颤振特性预测时必须考虑转静干涉作用;尾迹和势干扰的强度均随着轴向间距值的减小而加强,且都会加剧叶片气动弹性失稳.      

U型节流槽等压差活门内流场特性

以某U型节流槽等压差活门为研究对象,开展了内流场性能数值模拟研究.基于三维建模造型技术对所设计的压差活门进行初步建模,然后采用周期性网格网格单元划分等压差活门的结构化网格;进而通过CFD数值模拟进行了内流场仿真分析,并对不同出口节流开度的等压 差活门模型进行了对比研究.内流场状态表明:U型节流槽等压差活门不同流量以及不同出口节流开度下在节流口处由于面积突变,压力梯度变化较大,等压差活门的压降主要集中在此处,且均存在一定范围低速团与二次旋涡流等.仿真结果预测的外特性性能表明:等压差活门的压差在不同流量工况下和相同流量的不同出口节流开度下,压差维持在0.9MPa左右,符合设计要求.且不同出口节流开度下压差变化趋势相似,出口节流开度越大,压差越大,小流量下相应更快.      

带执行装置的压气机系统建模及仿真

针对压气机主动稳定控制对模型的要求,以Moore-Greitzer模型为基础,首先将模型进行空间离散化,用平均分布在压气机周向环面的离散位置点来描述流量扰动,建立了反映压气机周向动态特性的多维状态空间模型;其次以喷气装置作为主动稳定控制系统的执行装置,通过分析加入喷气装置后对流动区域产生的质量和动量影响,同时考虑气流从喷气装置出口到压气机起始平面存在的时间滞后,建立了带执行装置的压气机系统动态模型.以某压气机为例,对压气机失速行为及喷气状态下对失速的抑制作用进行仿真,结果表明:所建立的模型可以反映压气机旋转失速动态过程,通过控制喷气流量能拓展压气机的稳定工作范围,有效抑制压气机失速,模型可用于压气机主动稳定控制系统分析与设计.      

New constitutive relation for eddy viscosity models

A new turbulent constitutive relation was directly derived from Boussinesq's hypothesis and mixing length theory, and then implemented in the standard k-ε model. The performance of this constitutive relation was validated in zero pressure gradient flat-plate boundary layer flow, fully-developed turbulent channel flow and separated flow in a plane asymmetric diffuser. The investigation demonstrated that, this new constitutive relation gave very accurate results in the former two basic cases and provided significant improvement in prediction of separated and reattachment points in the plane asymmetric diffuser. Separation and reattachment points at x/H=7.5 and 29 were calculated accurately in comparison to experimental results, and the static pressure coefficient of 0.82 was very close to large eddy simulation calculation. These results are very encouraging but further verification and extensive application of the new constitutive relation to other two-equation eddy viscosity model are needed.      

引入压力梯度的针对角区分离流动的Spalart-Allmaras模型的改进

针对Spalart-Allmaras（S-A）模型在角区分离计算中的问题,将无量纲的压力梯度引入其涡黏性输运方程的生成项,得到了改进的S-A模型.通过对两套含角区分离的低速压气机叶栅进行验证计算发现:与实验结果相比,原始S-A模型所得的分离区偏大,分离区内壁面压力偏低;而改进模型得到了与实验一致的分离区尺寸以及吸力面、压力面压力系数分布等结果.针对S-A模型涡黏性生成项和耗散项的分析表明:引入的无量纲压力梯度有效的识别了角区分离,在分离区内改变了涡黏性的生成、耗散关系,增大了涡黏性,从而缩小了计算所得分离区,同时在主流区保留了原始S-A模型的计算结果,进而带来了良好的改进效果.      

煤基喷气燃料代用组分神经网络混合构建方法

为了建立航空燃料的喷雾模型,用于高保真液雾燃烧数值模拟,提出了基于人工神经网络混合模型的煤基喷气燃料代用组分构建方法.基于这一构建方法,重点针对煤基喷气燃料的雾化特性,利用多组分混合燃料的理化性质数据库对神经网络进行训练,获得了混合燃料理化性质隐式预测模型,结合随机投点优化方法,构建出能够很好地模拟煤基喷气燃料目标理化性质的代用组分.结果表明:该代用组分包含了5种碳氢化合物成分,摩尔分数为11.46%正癸烷、23.29%正十二烷、49.87%正十四烷、6.66%异辛烷和8.72%甲基环己烷.通过雾化特性实验,验证了代用组分对真实燃料雾化性能的模拟效果.该代用组分构建方法可以较好地解决混合燃料模拟过程中的非线性问题,通过改变目标理化性质可构建出相应代用组分.      

Experimental investigations of the spray structure and interactions between sectors of a double-swirl low-emission combustor

In this paper, the spray characteristics of a double-swirl low-emission combustor are analyzed by using Particle Imaging Velocimetry (PIV) and Planar Laser Induced Fluorescence (PLIF) technologies in an optical three-sector combustor test rig. Interactions between sectors and the influence of main stage swirl intensity on spray structure are explained. The results illustrate that the swirl intensity has great effect on the flow field and spray structure. The spray cone angle is bigger when the swirl number is 0.7, 0.9 than that when the swirl number is 0.5. The fuel distribution zone is larger and the distribution is more uniform when the swirl number is 0.5. The fuel concentration in the center area of the center plane of side sector (Plane 5) is larger than that of the center plane of middle sector (Plane 1). The spray cone angle in Plane 5 is larger than that in Plane 1. The width of spray cone becomes larger with the increase of Fuel–Air Ratio (FAR), whereas the spray cone angle under different fuel–air ratios are absolutely the same. The results of the mechanism of spray organization in this study can be used to support the design of new low-emission combustor.     

Research on hypersonic aircraft using pre-cooled turbojet engines

Systems analysis of a Mach 5 class hypersonic aircraft is performed. The aircraft can fly across the Pacific Ocean in 2 h. A multidisciplinary optimization program for aerodynamics, structure, propulsion, and trajectory is used in the analysis. The result of each element model is improved using higher accuracy analysis tools. The aerodynamic performance of the hypersonic aircraft is examined through hypersonic wind tunnel tests. A thermal management system based on the data of the wind tunnel tests is proposed. A pre-cooled turbojet engine is adopted as the propulsion system for the hypersonic aircraft. The engine can be operated continuously from take-off to Mach 5. This engine uses a pre-cooling cycle using cryogenic liquid hydrogen. The high temperature inlet air of hypersonic flight would be cooled by the same liquid hydrogen used as fuel. The engine is tested under sea level static conditions. The engine is installed on a flight test vehicle. Both liquid hydrogen fuel and gaseous hydrogen fuel are supplied to the engine from a tank and cylinders installed within the vehicle. The designed operation of major components of the engine is confirmed. A large amount of liquid hydrogen is supplied to the pre-cooler in order to make its performance sufficient for Mach 5 flight. Thus, fuel rich combustion is adopted at the afterburner. The experiments are carried out under the conditions that the engine is mounted upon an experimental airframe with both set up either horizontally or vertically. As a result, the operating procedure of the pre-cooled turbojet engine is demonstrated.